Technological Arts

Adapt9S12XDP512M2 XGATE MCU Module, Full Configuration

Click to enlarge

Product Info

Overview:

An enhancement of the popular HCS12 family (and fully backward-compatible CPU), the S12X family utilizes modern process technology. It boasts higher speed (40 MHz), more functionality, reduced power consumption and cost, and enhanced performance, with the XGATE RISC processor, on-chip memory-management, and DMA module. Adapt9S12XDP is a component of the "Adapt" Modular Prototyping System (AMPS) pioneered by Technological Arts. Unlike conventional evaluation and demo boards offered by other vendors, the flexible design of this system addresses the varied needs of evaluation, training, product development, proof-of-concept prototyping, and even volume production.

MCU Features:

The MC9S12XDP512 combines a full suite of on-chip peripherals, including 512K bytes of Flash, 32K bytes of RAM, 4K bytes of EEPROM, six asynchronous serial communication interfaces (SCIs), three serial peripheral interfaces (SPIs), an 8-channel Input Capture/Output Compare enhanced capture timer, an 8-channel, 10-bit analog-to-digital converter, a 16-channel, 10-bit analog-to-digital converter, an 8-channel pulse-width modulator (PWM), five CAN 2.0A, B software compatible modules (MSCAN12), two Inter-IC Bus blocks, and a Periodic Interrupt Timer. The MC9S12XDP512 has full 16-bit data paths throughout. Note that not all signals are brought out in the 112-pin version of the chip which is used on Adapt9S12X.

The following list summarizes the differences between the S12XD family and the S12 family.

• 40MHz operation
• 80MHz XGATE peripheral coprocessor
• Extended CPU instruction set
• additional Condition Code Register
• Programmable eight level interrupt controller
• Enhanced Memory Management Controller
• New four channel Periodic Interrupt Timer
• Improved Enhanced Capture Timer with modulus prescaler options
• Non-multiplexed 8MB expanded memory bus (144-pin package only)
• New low-power RC trigger and fast recovery from STOP modes
• Decimal prescaler for Real Time Interrupt module
• Improved SCI featuring hardware bit manipulation for LIN
• Enhanced trigger source options for Analog to Digital Converters
• Amplitude controlled Pierce oscillator
• Wider and deeper debug module

Module Overview:

Implemented in an "AdaptS12" form factor board, Adapt9S12XDP512 is compatible with an entire range of application cards, prototyping cards, and backplanes, and usable with solderless breadboards ("proto boards"). The module includes all necessary support circuitry for the MCU, as well as a 5-Volt regulator, RS232, RS485, and two CAN transceivers on-board.

Module Features:

MC9S12XDP512 MCU (112-pin)
16 MHz crystal
bus speed up to 40MHz (using on-chip PLL)
accommodates optional user-supplied oscillator
automotive-grade low-dropout 5V regulator (mounted on rear)
32K RAM
4K high-endurance EEPROM
512K high-endurance Flash
independent Flash blocks permit execution from one block while programming/erasing another block
fast in-circuit programming options:

load your S-record files via on-chip serial monitor using our free uBug12x GUI (Windows), or
use our USBDMLT pod (supports source-level debugging via CodeWarrior or NoICE)

no special Flash programming voltage or switch required
program in C, BASIC, Forth, assembler, etc.
Background Debug Mode (BDM) fully supported for loading and debugging user code
universal 6-pin/10-pin BDM connectors support BDM pods from multiple vendors
RS232 transceivers provided for two SCI channels
RS485 transceiver provided for a third SCI channel
two physical-layer high-speed CAN transceivers (PCA82C250)
one I2C interface
8-channel Input Capture/Output Compare Enhanced Capture Timer
dual 8-channel 10-bit analog-to-digital converter subsystems
8-channel PWM subsystem
periodic interrupt timer
includes low-voltage inhibit reset circuit + reset button
accommodates optional precision voltage reference chip for analog-to-digital converters
2.30" x 3.25" standard AdaptS12 form-factor card
two 50-pin connectors (H1 and H2) bring out all I/O pins of the MCU
all I/O pins on a 0.1" grid for easy interfacing to standard perfboard
versatile connector design for use with solderless breadboards, prototyping cards, or embedding into your design
stackable vertically or horizontally
convenient corner mounting holes
ideal development platform for all 9S12X variants

What's included:

assembled, tested module, pre-programmed with our 2K Serial Monitor
red and black power connector wire (#PCJ1-8)
printed schematic/pinout sheet
data sheets, manuals, and all other resources for this product can be found by clicking on the blue Resources tab above

If you require mating connectors, browse Connectors in the Components category at the left. For power supplies, browse the Accessories category.

Before you order...

All of our standard connector options are available for this board. The product photo above shows "RA1" connector on both H1 and H2. Please make your choice of connectors before adding this item to your shopping cart. Otherwise, the board will be shipped with the default option (no connectors on H1 and H2).

Choose Connector Option:
H1:
H2:

This product was added to our catalog on Thursday 01 December, 2005.

Product Info

Overview:

MCU Features:

The following list summarizes the differences between the S12XD family and the S12 family.

Module Overview:

Module Features:

What's included:

Product Details

Here are a couple of ways you can use Adapt9S12X:

Resources

MCU Documentation:

Module Documentation:

Tools and Utilities:

Examples

Training: