Technological Arts

Adapt9S12XEP100M2 XGATE MCU Module, Full Configuration

Click to enlarge

Product Info

NEW PRODUCT!

Overview:

The Freescale 9S12XEP microcontroller is an enhancement of the 9S12XD, with a CPU12X core operating at up to 50 MHz, an XGATE RISC co-processor operating up to 100 Mhz, larger on-chip memory resources (up to 1MB Flash and 64K RAM), enhanced memory access and error-correcting capabilities, additional addressing modes, and faster and higher-resolution analog-to-digital converter subsystems (12-bit resolution and 3us conversion time). Adapt9S12XEP is the latest member of the "Adapt" Modular Prototyping System (AMPS) pioneered by Technological Arts. Unlike conventional evaluation and demo boards offered by other vendors, the flexible design of this system addresses the varied needs of evaluation, training, product development, proof-of-concept prototyping, and even volume production.

MCU Features:

The MC9S12XEP100 combines a full suite of on-chip peripherals, including 1M bytes of Flash, 64K bytes of RAM, 4K bytes of EEPROM, six asynchronous serial communication interfaces (SCIs), three serial peripheral interfaces (SPIs), an 8-channel Input Capture/Output Compare enhanced capture timer, an 8-channel, 12-bit analog-to-digital converter, a 16-channel, 12-bit analog-to-digital converter, an 8-channel pulse-width modulator (PWM), five CAN 2.0A, B software compatible modules (MSCAN12), two Inter-IC Bus blocks, and a Periodic Interrupt Timer. The MC9S12XEP100 has full 16-bit data paths throughout. Note that not all signals are brought out in the 112-pin version of the chip which is used on Adapt9S12XEP.

The following list summarizes the differences between the S12XE family and the S12 family.

• 50MHz operation
• 100MHz XGATE peripheral coprocessor
• extended CPU instruction set
• additional Condition Code Register
• programmable eight level interrupt controller
• enhanced Memory Management Controller
• new four channel Periodic Interrupt Timer
• improved Enhanced Capture Timer with modulus prescaler options
• new low-power RC trigger and fast recovery from STOP modes
• decimal prescaler for Real Time Interrupt module
• improved SCI featuring hardware bit manipulation for LIN
• enhanced trigger source options for Analog to Digital Converters
• amplitude-controlled Pierce oscillator
• wider and deeper debug module

Module Overview:

Implemented in an "AdaptS12" form factor board, Adapt9S12XEP100 is compatible with an entire range of application cards, prototyping cards, and backplanes, and usable with solderless breadboards ("proto boards"). The module includes all necessary support circuitry for the MCU, as well as a 5-Volt regulator, RS232, RS485, and two CAN transceivers on-board.

Module Features:

MC9S12XEP100 MCU (112-pin)
4 MHz crystal
bus speed up to 50MHz (using on-chip PLL)
accommodates optional user-supplied oscillator
automotive-grade low-dropout 5V regulator (mounted on rear)
64K RAM
4K high-endurance EEPROM
1M high-endurance Flash
independent Flash blocks permit execution from one block while programming/erasing another block
fast in-circuit programming
Background Debug Mode (BDM) fully supported for loading and debugging user code
universal 6-pin/10-pin BDM connectors support BDM pods from multiple vendors

we recommend our low-cost USBDMLT pod for those using CodeWarrior

RS232 transceivers provided for two SCI channels
RS485 transceiver provided for a third SCI channel
two physical-layer high-speed CAN transceivers (PCA82C250)
one I2C interface
8-channel Input Capture/Output Compare Enhanced Capture Timer
dual 8-channel 12-bit analog-to-digital converter subsystems
8-channel PWM subsystem
periodic interrupt timer
includes low-voltage inhibit reset circuit + reset button
accommodates optional precision voltage reference chip for analog-to-digital converters
2.30" x 3.25" standard AdaptS12 form-factor card
two 50-pin connectors (H1 and H2) bring out all I/O pins of the MCU
all I/O pins on a 0.1" grid for easy interfacing to standard perfboard
versatile connector design for use with solderless breadboards, prototyping cards, or embedding into your design
stackable vertically or horizontally
convenient corner mounting holes
ideal development platform for all 9S12XE variants

What's included:

assembled, tested module, with blank flash, ready for use with any BDM pod
red and black power connector wire (#PCJ1-8)
printed schematic/pinout sheet
find data sheets, manuals, and all other resources for this product by clicking on the blue Resources tab, above

If you require mating connectors, browse Connectors in the Components category at the left. For power supplies, browse the Accessories category.

Before you order...

All of our standard connector options are available for this board. The product photo above shows "RA1" connector on both H1 and H2. Please make your choice of connectors before adding this item to your shopping cart. Otherwise, the board will be shipped with the default option (no connectors on H1 and H2).

Attention volume users!

We can customize this module to suit your needs (e.g. different crystal/oscillator, different MCU variant, selectively populated communications transceivers, etc.). Please contact us for a quote.

Choose Connector Option:
H1:
H2:

This product was added to our catalog on Sunday 06 June, 2010.

Product Info

NEW PRODUCT!

Overview:

MCU Features:

The following list summarizes the differences between the S12XE family and the S12 family.

Module Overview:

Module Features:

What's included:

Attention volume users!

Product Details

Resources

Module Documentation:

MCU Documentation:

Tools and Utilities:

Training: