You are here: Home STORE Microcontrollers 9S12 NanoCore12 NanoCore12C32ST Module, TTL Interface, 24-pin

Technological Arts Inc.

Your Shopping Cart

Your Cart is currently empty.

PDFPrint
NanoCore12C32S Module, RS232 Interface, 24-pinNC12DXC32 KIT 1

NanoCore12C32ST Module, TTL Interface, 24-pin
View Full-Size Image


NanoCore12C32ST Module, TTL Interface, 24-pin

Order Code: NC12C32ST
Price: USD $34.00


Product Info

This is the lowest-cost member of the NanoCore12 family-- a 24-pin DIP module with TTL serial pins. It is ready to be used with any USB-to-UART module (such as our USB2NCT product or other FTDI breakout) or your own RS232 level-shifter. Just plug it into a solderless breadboard or 24-pin DIP socket to start building your app! Free software development environments range from the new nqBASIC language (easiest for beginners) all the way up to C or Assembler, using CodeWarrior or GNU C.

Module Features:

  • based on the 9S12C32 MCU
  • includes 8 Mhz crystal
  • 24 MHz bus speed (via PLL)
  • local 5 Volt low-dropout 100 mA regulator
  • TTL-level signals for RX and TX
  • compatible with USB2NCT module for use with USB
  • has on-chip Serial Monitor (CodeWarrior-compatible)
  • supports standalone operation
  • 32K Bytes Flash
  • 2K Bytes Ram
  • 24-pin DIP form-factor
  • low profile (BDM connector omitted)
  • low-cost gold-plated 0.020" square pins
  • pinout virtually identical to BASICStamp2®

What you get:

  • this product ships with hardcopy data sheet and schematic diagram
  • data sheets, manuals, and all other resources for this product can be found at www.NanoCore12.com

®BASICStamp is a registered trademark of Parallax Inc.

Product Details

Ease-of-Use Features:

  • supports programming in C, BASIC, Forth, assembler, etc.
  • fast in-circuit programming
  • small footprint on-chip bootloader/monitor and free uBug12 GUI for quick loading/debugging of user programs on Windows, Mac, and Linux platforms
  • Run/Load switch for choice of Standalone or Monitor operation following reset
  • compatible with virtually all 9S12 development tools on the market

Flash-based code development using on-chip debug/monitor

With a 2K Flash-resident debug/monitor program, you'll be able to load your program into the remaining 30K Flash via the serial port using nqBASIC, CodeWarrior, or uBug12. The entire 30K Flash can be programmed in about 3 seconds! To use the monitor for debugging or code-loading, just set the switch to LOAD. To run your standalone program thereafter, leave the switch at RUN.  A program you load into Flash this way will run every time you apply power or reset the board in Run Mode.

Flash-based code development using a BDM pod

If you want to take advantage of a more advanced development tool (such as USBDMLT), the entire 32K Flash can be used, because the Flash-resident bootloader is no longer needed.

Detailed features:

  • capable of 3-Volt operation
  • optional standard 6-pin BDM connector supports full debugging capabilities (with an optional BDM pod)
  • ECLK signal is user-accessible (via pad on circuit board)
  • access to eight 10-bit analog input or digital I/O port lines (Port AD)
  • access to eight digital I/O port lines (Port T)
  • up to five PWM timer channels (PT0 - PT4)
  • up to eight Input Capture/Output Compare pins (Port T)
  • internal programmable pullup and pulldown resistors on most pins
  • user access to MCU reset signal


Availability

Usually ships in:

1day.gif

Customer Reviews:

There are no reviews yet for this product.
Please log in to write a review.


more categories


Modules

Modules


Packages

Packages


App Cards

App Cards


Accessories

Accessories


Select & click to change


List All Products


Advanced Search





Forgot your password?
Forgot your username?
No account yet? Register