Print
BDM Pod for HC12 and S12 Targets, RS232 InterfaceXGATE BDM Pod for 5-Volt targets, RS232 Interface

BDM Pod for HC12 and S12 Targets, USB Interface
View Full-Size Image


BDM Pod for HC12 and S12 Targets, USB Interface

Order Code: UBDM12LXU5
Price: USD $249.00


Product Info

This BDM pod supports most HC12 and S12 chips, and is compatible with both 6-pin and 10-pin target BDM connectors. It requires no external power, as it receives power from your target board. It is compatible with 5V targets.

Features:

  • low-cost BDM pod for all HC12 and S12 targets (not including S12X)
  • works only with 5-Volt targets
  • use Freescale D-Bug12 commands on target board
  • supports hardware and software breakpoints in target
  • USB interface to PC (or any platform with terminal emulation capability)
  • 10-pin ribbon cable (superset of standard 6-pin BDM pinout), compatible with all Adapt12 and Adapt9S12 boards, as well as most other vendors' boards
  • no power supply required-- draws power from target board
  • housed in a robust plastic enclosure for maximum reliability
  • includes power and activity indicator LEDs
  • based on a 9S12DG128 MCU running D-Bug12 version 4.0
  • supports baud rates up to 115K (default is 9600 baud)
  • compatible with NoICE12 debugger
  • supplied with miniB USB cable
  • based on FTDI USB-to-UART chip (requires one-time installation of USB driver)

Chips supported:

68HC812A4, 68HC912B32, 68HC912BC32, 68HC912D60/A, 68HC912DA128/A, 68HC912DG128/A, 68HC912DT128/A, and all current 9S12 derivatives (supports only 5V operation). Can communicate with 9S12X chips, but does not support Flash erase/program nor the XGATE co-processor. Our USBDMLT pod is the recommended alternative for 9S12X chips.

Product Details

Here's how to use MicroBDM12LXU5:

Just connect the supplied ribbon cable to the target board's "BDM IN" connector. The target board could be any Adapt12-family board, or any other 'HC12 or 9S12 board that has a 6- or 10-pin BDM interface connector. Just be sure to line up the pin 1 indicator with pin 1 on the BDM connector. The host for the BDM Pod can be any type of computer running a terminal program. The BDM pod will receive its 5V operating power from the target board through the ribbon cable. A couple of suggested Windows terminal programs: TeraTermPro, MiniIDE, Hyperterminal. For details on using other terminal programs with D-Bug12, refer to the D-Bug12 Manual.

The big advantage of using a BDM pod is that it frees up all of the target board's memory for your application, while still offering you debugging capability. You can examine memory and registers, disassemble a memory range, set breakpoints, and do tracing in the target board's on-chip memory, among other things.

What's inside the box:

MicroBDM12LXU5 is a minimal 9S12 board, running D-Bug12 v4.0. It consists of the MCU, a crystal, a DB9 with integral USB interface circuit, and a few miscellaneous components, all mounted on a small board less than 2 inches square. A 10-pin ribbon cable is attached to one edge, a miniB USB connector is on the opposite edge, and the whole assembly is housed in a small plastic box. A miniB USB cable is included for the PC USB port interface.

Firmware Updates:

If D-Bug12 ever needs to be updated, it can be done using another BDM pod. By opening the box, applying a DC voltage (5 to 9V, nominal) to the power connector on the circuit board, and moving two jumpers to make the ribbon cable function as BDM IN, the board becomes a target, and Flash can be erased and re-programmed as needed.

Availability

Usually ships in:

instock.gif



more categories


NanoCore12

NanoCore12


Adapt9S12C

Adapt9S12C


Adapt9S12D

Adapt9S12D


Adapt9S12E

Adapt9S12E


Adapt9S12P

Adapt9S12P


Adapt9S12X

Adapt9S12X


Esduino

Esduino


neCore12

neCore12


Debugging Tools

Debugging Tools