You are here: Home STORE Microcontrollers Debugging Tools BDM Pod for HC12 and S12 Targets, RS232 Interface

Technological Arts Inc.

Your Shopping Cart

Your Cart is currently empty.

Solderless Breadboard, 830 tie pointsBDM Pod for HC12 and S12 Targets, USB Interface

BDM Pod for HC12 and S12 Targets, RS232 Interface
View Full-Size Image

BDM Pod for HC12 and S12 Targets, RS232 Interface

Order Code: UBDM12LX5
Price: USD $199.00

Product Info

This BDM pod supports most HC12 and S12 chips, and is compatible with both 6-pin and 10-pin target BDM connectors. It requires no external power, as it receives power from your target board. It is compatible with 5V targets.


  • low-cost BDM pod for all HC12 and S12 targets (not including S12X)
  • works only with 5-Volt targets
  • use D-Bug12 commands to interact with target MCU
  • supports hardware and software breakpoints in target
  • RS232 interface to PC (or any platform with terminal emulation capability)
  • 10-pin ribbon cable (superset of standard 6-pin BDM pinout), compatible with all Adapt12 and Adapt9S12 boards, as well as most other vendors' boards
  • no power supply required-- draws power from target board
  • housed in a robust plastic enclosure for maximum reliability
  • includes power and activity indicator LEDs
  • based on a 9S12DG128 MCU running D-Bug12 version 4.0
  • supports baud rates up to 115K (default is 9600 baud)
  • compatible with NoICE12 debugger
  • supplied with serial cable

Chips supported:

68HC812A4, 68HC912B32, 68HC912BC32, 68HC912D60/A, 68HC912DA128/A, 68HC912DG128/A, 68HC912DT128/A, and all current 9S12 derivatives (supports both 5V and 3V operation). Can communicate with 9S12X chips, but does not support Flash erase/program nor the XGATE co-processor. Our USBDMLT pod is the recommended alternative for working with 9S12X MCUs.

NOTE: if you need USB connectivity, you may wish to consider UBDM12LXU5 instead


Product Details

Here's how to use MicroBDM12LX5:

Just connect the supplied ribbon cable to the target board's "BDM IN" connector. The target board could be any Adapt12-family board, or any other 'HC12 or 9S12 board that has a 6- or 10-pin BDM interface connector. Just be sure to line up the pin 1 indicator with pin 1 on the BDM connector. The host for the BDM Pod can be any type of computer running a terminal program. The BDM pod will receive its 3V or 5V operating power from the target board through the ribbon cable. A couple of suggested Windows terminal programs: TeraTermPro, MiniIDE, Hyperterminal. For details on using other terminal programs with D-Bug12, refer to the D-Bug12 Manual.

The big advantage of using a BDM pod is that it frees up all of the target board's memory for your application, while still offering you debugging capability. You can examine memory and registers, disassemble a memory range, set breakpoints, and do tracing in the target board's on-chip memory, among other things.

What's inside the box:

MicroBDM12LX5 is a minimal 9S12 board, running D-Bug12 v4.0. It consists of the MCU, a crystal, an RS232 interface circuit, and a few miscellaneous components, all mounted on a small board less than 2 inches square. A 10-pin ribbon cable is attached to one edge, and a 9-pin D-sub connector is on the opposite edge, and the whole assembly is housed in a small plastic box. A 9-pin serial cable is included for the PC serial port interface.

Firmware Updates:

If D-Bug12 ever needs to be updated, it can be done using another BDM pod. By opening the box, applying a DC voltage (5 to 9V, nominal) to the power connector on the circuit board, and moving two jumpers to make the ribbon cable function as BDM IN, the board becomes a target, and Flash can be erased and re-programmed as needed.


Usually ships in:


List All Products

Advanced Search

Forgot your password?
Forgot your username?